A Drying Chamber Part
-
D-Type Acrylic Manifold Chamber D-Type Acrylic Manifold Chamber
In the acrylic manifold, flask lyophilization is possible and the chamber body of the acrylic material is the device to be able to observe lyophilization process of sample at all the viewing angles in the chamber
- Acrylic manifold Top Lid: select 6, 8, 12 port (the vacuum valve is equipped according to the number of port selected)
- Circular acrylic body
- Acrylic Floor Lid: Circular (36∅) type vacuum induction port.
-
D-type stainless steel manifold chamber D-Type SUS Manifold Chamber
n the acrylic manifold, flask lyophilization is possible and applied with the chamber body of STS-304 material, which is corrosion resistant material, it is the chamber protected from the corrosion by the chemical samples
- Acrylic manifold Top Lid: select 6, 8, 12 port (the vacuum valve is equipped according to the number of port selected)
- Circular acrylic body
- Acrylic Floor Lid: Circular (36∅) type vacuum induction port.
-
MPA Chamber Multi-purpose Acrylic Chamber
In the acrylic manifold, flask lyophilization is possible, the chamber body of acrylic material allows observing the lyophilization process of the sample in the chamber at all viewing angles and is the chamber designed with floor lid in order to be installed at the top to pre-freeze or lyophilize the multi-layer of small shelf contained the sample (mini-tray) through the acrylic floor lid exclusively for mini-tray pre-freezing
- Acrylic manifold Top Lid: select 6, 8, 12 port (the vacuum valve is equipped according to the number of port selected)
- Circular acrylic body
- Acrylic Floor Lid: Exclusively for mini-tray pre-freezing
-
MPA-MH chamber Multi Purpose Acrylic-Mini tray Heating Chamber
This is the chamber designed to supply sublimation heat to the mini-tray by having power supply connection jack at the acrylic floor lid exclusively for the heated mini-tray or prefreezing besides the basic specification of MPA chamber
- Acrylic manifold Top Lid: select 6, 8, 12 port (the vacuum valve is equipped according to the number of port selected)
- Circular acrylic body
- Acrylic Floor Lid: Exclusively for heated and pre-freezing mini-tray
- Heated mini tray
- Power connector and connection jack set
-
MPS Chamber Multi-purpose Stainless Chamber
In the acrylic manifold, flask lyophilization is possible and as a chamber applied with STS-304 material, which is corrosion resistant material, this is the chamber designed to be install at top of the equipment in order to pre-freeze or lyophilize the multi-layer small shelf (mini-tray) contained the sample through the acrylic floor lid exclusively for the heated mini-tray or pre-freezing
- Acrylic manifold Top Lid: Select 6, 8, 12 port (the vacuum valve is equipped according to the number of port selected)
- Circular acrylic body
- Acrylic Floor Lid: Exclusively for mini-tray pre-freezing
-
T-type manifold T-Type Manifold
As the most economic structure out of the lyophilization methods using flask, it can utilize the diverse accessories through T-manifold
- T-manifold (SUS304): Select 6, 8, 12, 24 port (the vacuum valve is equipped according to the number of port selected)
- Acrylic Floor Lid: Exclusively for T-manifold
-
Stoppering chamber Stoppering Chamber
Lyophilization using flasks by connecting with manifold is possible. the chamber body of acrylic material allows observing the freeze the freeze drying process of the sample in chamber at all viewing angles and the stoppering system installed in the top lid can load 140 vials(based on 10ml vial)
- Acrylic manifold Top Lid: Select 6, 8, 12 port (the vacuum valve is equipped according to the number of port selected)
- Circular acrylic body
- Acrylic Floor Lid: Exclusively for mini-tray pre-freezing
-
Flask stoppering device Flask Stoppering Device
Manufactured with small size, it has a structure that can be installed at 2000ml flask, installing up to 24 vials. It allows observing the sample inside the vial through the feedthrough installed as basic. It is easy to separate and wash and depending on the case, it can be sterilized in the autoclave (flask needs to be purchased separately)
- Manufactured so as to be loaded in 2000ml flask
- 24 holes (use 5-20ml vial)
- Feedthrough is equipped basically (thermocouple K)
- As a small size easy to separate, it has a structure that the washing and sterilization are possible
B Vacuum Part
-
Vacuum Pump
Pump that connected to the lyophilizer, forms the vacuum
- Inlet / Outlet : NW25
- Ultimate Pressure : ≤1X10-3 Torr
- Power : 220V 1Phase
- Gas Ballast
-
Oil Mist Trap A-Type Oil Mist Trap A-Type
This is the filtering device to filter the oil mist generated at the outlet side when operating vacuum pump
- Exhaust filter exclusively for 100-400L vacuum pump
- Size: NW25
- External Material: Poly carbonate (PC)
- Weight: 0.38 kg
-
High Vacuum OIL
- Capacity Selection : 1L, 4L
-
Vacuum grease Vacuum Grease
Applied to the areas where the air tightness is required such as valve, O-ring, etc. installed at the lyophilizer, it forms the vacuum effectively
- High Vacuum Grease(USA)
- weight : 150g
- Can be used in the range between -50℃ and +200℃
- It is easy to use as it is tube-type
-
Chemical trap A type, B type
A-type and B-type chemical traps are filters to secondarily protect the vacuum pump from foreign substances and corrosive substances generated in samples, cold traps, and drying chambers. Activated carbon and micron filters are applied. It is a device that effectively protects the vacuum pump through superior filtering effect, and is manufactured in a size that is easy to install on the LYB table.
- Filter inside size: A type ∅130 × 125L, B type ∅130 × 250L
- material : STS-304 ‣ NW25 standard
- Active Carbon & Micron Filter(5㎛) applied
C Accessories
-
Mobile table for exclusive use of LYB LYB Series Moving Table
As a table to mount the LYB series lyophilizer at the top and the vacuum pump at the bottom, it is easy to move because it has horizontal fixed caster and can fix the position on the uneven floor by adjusting the level
- Design optimized for LYB
- Equipped with horizontal fixed caster
- Enable to install vacuum pump and chemical trap exclusively for LYB
-
Mini Tray Mini Tray
Mini-tray that the pre-freezing and lyophilization inside of cold trap of lyophilizer. Material is STS-304 corrosion resistant and composed of 3-5 shelves. In case of heated type, it can accelerate the drying speed by supplying the heat of sublimation
- STS-304material
- Select either 4-layer or 5-layer
- Fixing pin to prevent the tray break-away
- Handle at the top
-
Tube Holder Exclusive for D-Type Drying Chamber
Tube holder (STS304) is the product for lyopilization by installing multiple conical tube in the D-type drying chamber
- L : 15ml Conical Tube (124 Hole)
- M : 15ml Conical Tube (58 Hole)
- S : 15ml Conical Tube (19 Hole) / 2000ml For flask
- L : 50ml Conical Tube (37 Hole)
- M : 50ml Conical Tube (19 Hole)
- S : 50ml Conical Tube (7 Hole) / 2000ml For flask
-
Vacuum valve Vacuum Valve
As a value to connect the accessories with manifold, it serves to form or release the vacuum in the accessory, and if FPRP filter pack is installed, it supplies the air or N filtered with 0.2μm to inside of flask
[ FPRP filter Pack ]- N2 injection kit (regulator, hose exclusively for N2 injection 3m, special nipple 12ea)
- 0.2μm filter 1 pack (50ea)
-
flask Flask
As q flask exclusively for lyophilization manufactured with first class hard (borosilicate) glass, it is the product for lyophilization in diverse methods
- 150ml (OD∅56 × H85)
- 300ml (OD∅56 × H160)
- 700ml (OD∅90 × H135)
- 900ml (OD∅90 × H190)
- 1200ml (OD∅90 × H240)
- 2000ml (OD∅120 × H225)
-
adapter Adapter
It is the device to connect the accessories such flask, etc. in various ways and it is the product manufactured with glass and stainless material and in the form of L or straight line
- Glass 45° adapter (hard 1st grade Borosilicate)
- Stainless 45° adapter(STS-304)
- Stainless straight line adapter (STS-304)
-
Wide Mouth Wide Mouth / Flask Cap
The product to mount the diverse type of flask in the manifold
- A type (for 150ml ~ 300ml flask)
- B type (for 700ml ~ 1200ml flask)
- C type (for 2000ml flask)
- D type (for 29/32 flask)
-
FSD Pack Flask Sublimation Device Pack (Cannot select 4L)
This is the product to mount the large volume flask or accelerate the lyophilization speed, it is the combination of device that supply the heat of sublimation (waste heat) to the flask through diffuser, which induces the waste heat generated in the lyophilizer toward the flask.
- Main unit of variable flask rack (purchase of individual unit is possible_) Select either 2 hole (main unit of 4-8L class/ 4 hole (main unit of 15L class)
- WTV (Wide Mouth to Vacuum Valve) connector 6ea
- Dedicated Vacuum Hose (4m)
- Sublimation Heat (Waste Heat of Compressor) Diffuser Kit
-
FPRP filter Pack Flask Purify Release Port
Product to inject N2 (nitrogen) and the clean air or to perform filtering when releasing the vacuum in the main unit in order to prevent the cross contamination of sample after completing the lyophilization
- 5㎛ vacuum release filter (1Ea)
- N2 or clean air injection port
- Ne Injection Kit (regulator, hose for N2 injection 3m)
-
Differential pressure monitoring system (DPMS)
DPMS (Differential Pressure Monitoring System) is the device to analyze the amount of intake air and discharged air of radiator linked to control unit and it detects and alerts the situation that the differential pressure occurs in the room where the lyophilizer is installed or that the unbalance of air circulation occurs by clogging the dust filter.